Description
OV5640 – 5.0 MP Camera Module:
The OV5640 – 5.0 MP Camera Module (B0158) is based on the OV5640 color sensor from OmniVision.
The sensor has a 1/4.0″ optical format, which combined with the pixel size of 1.4 µm x 1.4 µm, results in the 5.0 MP 2592 x 1944 VGA | WVGA | SXGA | UXGA | QXGA image. This is a rolling shutter sensor, which captures an entire column (or row) simultaneously, and compiles the image by scanning across (or down). The lens and/or sensor have an IR-cut filter, so this module is not appropriate for low-light photography. This module does not have a lens mount, but relies on the optics supplied with the sensor.
Use this camera module on a Windows, Linux, or Raspberry Pi USB connection with the ArduCAM USB Camera Shield on the primary interface (a 20-pin 0.1″ / 2.54 mm pitch interface), or your custom-built interface. ArduCAM supplies a wide variety of camera modules that are compatible with the USB Camera Shield, and all are available from DLSCorp.
Camera Shields:
In the Arduino world, a “shield” is a piggy-back circuit board that provides additional functionality to the development board. In this context, a camera shield provides the required interface from the camera module to your computer. You may choose to create your own custom-built hardware interface via the 20-pin 0.1″ pitch connector. Or, you may purchase one of the available ArduCAM camera shields.
Use this camera module on a Windows, Linux, or Raspberry Pi USB connection with the ArduCAM USB Camera Shield on the primary interface (a 20-pin 0.1″ / 2.54 mm pitch interface), or your custom-built interface. ArduCAM supplies a wide variety of camera modules that are compatible with the USB Camera Shield, and all are available from DLSCorp. You may use the ArduCAM F Shield Rev V2 or the ArduCAM LF Shield Rev V2 to connect to Arduino system boards. Open-source software and binaries are provided on the ArduCAM GitHub site (see link below) for these shields.
Additional Details:
OmniVision CAMERACHIP™ image sensors are low voltage CMOS devices that provide the full functionality of a single-chip camera and image processor in a small footprint package. They provides full-frame, sub-sampled, scaled or windowed 8-bit/10-bit images in a wide range of formats, controlled through the Serial Camera Control Bus (SCCB) interface. All required image processing functions, including exposure control, gamma, white balance, color saturation, hue control, white pixel canceling, noise canceling, and more, are also programmable through the SCCB interface. A compression engine provides for increased processing power. In addition, OmniVision CAMERACHIP sensors use proprietary sensor technology to improve image quality by reducing or eliminating common lighting/electrical sources of image contamination, such as fixed pattern noise, smearing, etc., to produce a clean, fully stable color image.
Features:
- Onboard LDO regulators for 2.8V and 1.8V
- Single 3.3V power input
- 2.54 mm (0.1 inch) standard pin out
- Open source project supported by www.ArduCAM.com
- active array size: 2592 x 1944
- power supply:
core: 1.5VDC + 5% (internal regulator)
analog: 2.6 ~ 3.0V
I/O: 1.8 ~ 32.8V - output formats :
(8-bit): YUV(422/420) / YCbCr422,
RGB565/555/444, CCIR656,
8-bit compression data,
8/10-bit raw RGB data - lens size: 1/4″ optical format
- autofocus control
- input clock frequency: 6 ~ 27 MHz
- shutter: rolling shutter
- maximum image transfer rate:
5 megapixel (2592 × 1944): 15 fps (and any size scaling down from 5 megapixel) QSXGA
XGA (1080): 30 fps - scan mode: progressive
- pixel size: 1.4 μm x 1.4 μm
- image area: 3673.6 μm x 2738.4 μm
- Interface: Parallel RAW, RGB, YUV, JPEG output
- 8 g / 40 mm x 40 mm x 12 mm
Applications:
- Cellular phones
- PDAs
- Toys
- Other battery-powered products
- ARM based platforms
Package includes:
- 1x CMOS OV5640D AF Camera Module 1/4-Inch 5-Megapixel Module
Reviews
There are no reviews yet.