MT9P001 – 5.0 MP M12 Mount Camera Module w/ LS-6020 Lens

$34.99

6 in stock (can be backordered)

Description

MT9P001 – 5.0 MP M12 Mount Camera Module w/ LS-6020 Lens

The MT9P001 – 5.0 MP M12 Mount Camera Module w/ LS-6020 Lens is based on the MT9P001 color sensor from ON Semi.

The sensor has a 1/2.5″ optical format; the pixel size of 2.2 µm x 2.2. µm results in the 5.0 MP 2592 x 1944 [VGA | WVGA | SXGA- | SXGA | UXGA | QXGA | WQXGA+] image. This is a rolling shutter sensor, which captures an entire column (or row) simultaneously; the sensor compiles the image by scanning across (or down).. The lens and/or sensor have an IR-cut filter, so this module is not appropriate for low-light photography. The standard lens mount for this module is the M12 mount, and ships with the LS-6020 lens. The key benefit of the standardized lens mount is the simplicity in swapping the lens – fisheye, wide-angle, telephoto, zoom, NoIR filter – all of which are available from DLSCorp. Note that this camera module can be special-ordered with either mount and any compatible lens.

The camera module provides a 30-pin flexible flat cable interface, which fits the ArduCAM USB Camera Shield or ArduCAM USB3.0 Camera Shield (or your custom-built interface). ArduCAM supplies a wide variety of camera modules, all are compatible with the USB Camera Shield, and all are available from DLSCorp.

Features:
  • M12 mount lens holder,
  • LS-6020 lens
  • 1/2.5” optical format (sensor size)
  • High sensitivity for low-light operation
  • Standard SCCB interface
  • Output support for Raw RGB, RGB (RGB565/555), GRB422, YUV (422/420) and YCbCr (4:2:2) formats, JPEG compression formats
  • Automatic image control functions
  • Image quality controls including color saturation, gamma, sharpness (edge enhancement), lens correction, white pixel canceling, noise canceling, and 50/60 Hz
  • Low operating voltage for embedded portable apps
  • Board Size: 30.5 x 30.5mm
 Pinouts:

Table 1 – Secondary Interface

Pin No. PIN NAME TYPE DESCRIPTION
1 GND Ground Power ground
2 FLASH Input Flash output control
3 Trigger Output Exposure synchronization input
4 VSYNC Input Active High: Frame Valid; indicates active frame
5 HREF Input Active High: Line/Data Valid; indicates active pixels
6 DOUT11 Input Pixel Data Output 11 (MSB)
7 DOUT10 Input Pixel Data Output 10
8 DOUT9 Input Pixel Data Output 9
9 DOUT8 Input Pixel Data Output 8
10 DOUT7 Input Pixel Data Output 7
11 DOUT6 Input Pixel Data Output 6
12 DOUT5 Input Pixel Data Output 5
13 GND Ground Power ground
14 DOUT4 Input Pixel Data Output 4
15 DOUT3 Input Pixel Data Output 3
16 DOUT2 Input Pixel Data Output 2
17 DOUT1 Input Pixel Data Output 1
18 DOUT0 Input Pixel Data Output 0(LSB)
19 XCLK Output Master Clock into Sensor
20 PCLK Input Pixel Clock output from sensor
21 SCL Input Two-Wire Serial Interface Clock
22 SDATA Bi-directional Two-Wire Serial Interface Data I/O
23 RST Output Sensor reset signal, active low
24 GND Ground Power ground
25 GND Ground Power ground
26 STANDBY Output Standby-mode enable pin (active HIGH)
27~30 VCC POWER 3.3v Power supply
Package includes:
  • MT9P001 – 5.0 MP M12 Mount Camera Module w/ LS-6020 Lens (qty 1)
Additional Resources:

Additional information

Weight 2 oz
Dimensions 1 × 1 × 1 in

Reviews

There are no reviews yet.

Be the first to review “MT9P001 – 5.0 MP M12 Mount Camera Module w/ LS-6020 Lens”

Your email address will not be published. Required fields are marked *